Close this search box.

Minn Kota Trolling Motor Foot Pedal Problems – Things to Consider

minn kota trolling motor foot pedal problems

Imagine you’re out on the river fishing with your favorite boat. When the foot pedal for your trolling motor starts, it acts erratically. This issue with the Minn Kota Trolling foot pedal not working has been around for a while.

This has been going on for an extremely long time. But there are excellent answers and treatments for this, just as there are for other problems.

Minn Kota Trolling foot pedal problems- what to do?

Poor construction all the way down to the fragile link, broken foot pedal, poor insulation, incorrect load in, and fixed-angle steering. These are the problems you can face.Then there are the faulty switches, the stuck buttons, the nonworking motor, etc. These are, by and large, the most typical.

Several other factors may lead to a malfunctioning foot pedal on a Minn Kota trolling motor.

We’ll go over each of these solutions in detail throughout the article. So you can avoid any future hassles.

Without further ado, let’s get down to business.

Issues with the Foot Pedal on Your Minn Kota Trolling Motor

There are a number of potential causes for the inoperable state of your Minn Kota trolling motor foot pedal. The specific issue can differ depending on both the model and software version you have.

Stains on the sensor board are the most common cause of the Minn Kota Trolling motor foot pedals. It hinders to function of older models.

On the other hand, difficulties with the connectors and other such nonsense plague even the moderately new ones. Here, however, we will show you every conceivable reason that can cause

The foot pedal on your Minn Kota Trolling has stopped responding. There’s absolutely no need to fret about it. In other words, go ahead and get

With the progression of this article; in the end, you will acquire all the issues at hand.

This is a list of the most typical explanations-

A Sensor Board With Significant Degradation

If you’ve invested in a quality trolling motor, you won’t have to worry about the foot pedal breaking. This suggests an issue with earlier versions of the Minn Kota.

Which is to say, the circuit board full of sensors will gradually deteriorate over time. This may happen when Minn Kota trolling motor prop not spinning. But don’t let that scare you.

You-Can-Do (DIY) tricks suggest you can quickly and easily eliminate the problem. Fixing a faulty sensor board isn’t rocket science or a tough nut to crack.


However, you can always replace the board if fixing it seems impossible. It can be done from either or a local repair shop. Both are worthwhile endeavors.

In the event of a malfunction, you must replace the sensor board.  This is a good habit to get into.

Fragile Link

Minn Trolling motor foot pedal stops working

For your trolling motor to function, the power connection at the foot pedal must remain closed at all times. In order to get rid of it, a thorough examination of the cable management is required.


If your Minn Trolling motor foot pedal stops working, check the power cables.

Invest some effort and double-check all of the wires and plugs.

If you find a connection that isn’t securely fastened, you need to secure it in the right way. This will help you with Minn Kota deckhand 40 issues.

Get in Touch with a Specialist

This is the absolute worst-case scenario imaginable. If you find yourself on the verge of perplexity, you can put this into practice. This isn’t a real-time configuration process, but you can fix your Minn Kota Trolling quickly.

Both of these are the most typical causes of your Minn Kota Trolling foot pedal stopping working. Regardless, resolving either of these issues is a breeze.


As you just saw, it’s not hard to go and fix it. Be calm. Prepare yourself by hydrating thoroughly and diving right in. I hope that your day is filled with success!

If you’re having trouble with your Minn Kota Ultrex and can’t figure out what’s wrong, call the company. That is, you ought to consult an expert. If you follow suit,  they’ll replace damaged parts on their own.

Fixing a Broken Foot Pedal for a Trolling Motor

Fixing a Broken Foot Pedal

To someone unfamiliar with trolling motors, the foot pedal may as well be the trolling motor’s heart. After all, it controls the entire device.

Similarly, you can’t control the trolling motor’s speed without the foot pedal. Perhaps you have experienced firsthand the significance of the foot pedal.

However, fixing the problem with the foot pedal is the primary focus here. The trolling foot pedal stopped working, and now what?

Maybe you’re imagining that a replacement will be provided. In any case, that’s not a bad argument. In nearly every instance, obtaining the trolling food pedal replacement is within reach.

In any event, you should start by making sure the problem has been properly validated. You can’t possibly expect to discover a solution to the issue if you can’t.

The two issues I highlighted above are possible in the vast majority of situations. Yet, other issues, such as power outages, faulty control boards, and so on. In order to thoroughly search for that and examine the whole system for proper boat maintenance.

Take the necessary steps to fix the issue. Ultimately, if you still can’t get it to work, you’ll have to get a new foot pedal.

Well, there’s that. However, it’s far too complicated, right? Right now, you should proceed! Make progress any way you can.

Is There a Recommended Way to Use the Trolling Foot Pedal

Trolling Foot Pedal

Knowing how to properly use the trolling foot pedal will help you avoid both major and minor hassles. Here, though, we’ll show you how to use the foot pedals to switch sides.

It’s riskier, and we’ve seen a lot of first-timers get hurt trying it. So we think people should be aware of that. If you want to know how to do something, here are the instructions:

  • To go right, remove your foot from the pedal and tap “toe down.” Stop doing the opposite and start doing things the right way. You’ll be unable to make progress on the right path if you do.
  • To go left, tap the “hill down” button. The “hill down” could be located in a few different spots. Do not start working until you have found the item.
  • However, you can use the same fundamental approach you already know to make progress. In that scenario, things would stay the same. There you go!

How Do You Adjust A Minn Kota Foot Pedal?

It becomes urgent to adjust the Minn Kota foot pedal in its right place while it gets away from its alignment. In that case, you have to check out the Minn Kota foot pedal instructions.

Following the given simple steps, you can adjust your Minn Kota foot pedal with ease-

  • Lid off the trolling motor and lift out the gear
  • Prevent the keeper screw
  • Move the place the foot pedal straight into its position
  • Make sure it matches the prop
  • Slide the trolling motor gear into its place.
  • You are done with the Minn Kota trolling motor foot pedal adjustment.


If you have a Minn Kota, how do you change the settings on the foot pedal?

To change the settings on a Minn Kota trolling foot pedal, follow these steps:

  • Turn off the motor and disconnect the power source.
  • Remove the cover on the foot pedal by using a screwdriver to remove the screws.
  • Locate the adjustment screw, which will be labeled as “sensitivity” or “tension” on the foot pedal.
  • Use a screwdriver to turn the adjustment screw clockwise to increase the sensitivity or counterclockwise to decrease the sensitivity.
  • Reattach the cover to the foot pedal using the screws.
  • Test the new setting on the water to determine if further adjustments are necessary.

It is important to note that the specific location of the adjustment screw may vary depending on the model and age of the Minn Kota trolling foot pedal. Consult the owner’s manual or contact Minn Kota customer service for assistance if necessary.

Just how do you cinch down the foot pedal on a Trolling?

To cinch down the foot pedal on a trolling motor, follow these steps:

  • Locate the tension adjustment knob on the bottom of the pedal.
  • Turn the adjustment knob clockwise to increase the tension or counterclockwise to decrease the tension.
  • Test the tension of the foot pedal by pressing down on it with your foot. If it feels too loose, continue to increase the tension until it feels secure.
  • If the foot pedal is still too loose, check the bolts and screws that attach it to the mounting bracket. Tighten any loose bolts or screws with a wrench or screwdriver as needed.
  • Once you have achieved the desired tension, use the lock lever on the mounting bracket to secure the foot pedal in place.

It is important to regularly check the tension and security of the foot pedal to ensure safe and efficient operation of the trolling motor. If you have any concerns or questions, consult the owner’s manual or contact the manufacturer for assistance.

Approximately how big is the Trolling foot pedal?

The size of a trolling foot pedal can vary depending on the model and brand, but on average, they measure between 6 to 8 inches in width and 10 to 12 inches in length. However, some models may be smaller or larger depending on the specific features and design of the trolling motor.

How does a foot pedal switch work?

How does a foot pedal switch work

A foot pedal switch is an electrical switch that is activated by pressing down on a pedal with your foot. The switch is connected to a device or machine that needs to be turned on or off, such as a sewing machine or a power tool.

When you press down on the foot pedal, it activates a mechanism inside the switch that closes an electrical circuit.

This allows current to flow from the power source to the device or machine, turning it on.

When you release your foot from the pedal, the mechanism opens the circuit, cutting off the current and turning the device or machine off.


We’re hoping you’ve already figured out the answers to the questions we’ve been discussing. If that’s the case, it’s time for us to part ways.

We’d like you to have a complete and total understanding of what we talked about. That is minn kota trolling motor foot pedal problems.

If you feel as though you have missed something crucial, we suggest reading the article again. And please forward this listing to your associates.

But help other people, and you’ll help yourself. we hope you have a wonderful time boating!

Related Articles